Types of Cooling Systems
Air conditioning, or cooling, is more complicated than heating. Instead of using energy to create heat, air conditioners use energy to take heat away. The most common air conditioning system uses a compressor cycle (similar to the one used by your refrigerator) to transfer heat from your house to the outdoors.
Picture your house as a refrigerator. There is a compressor on the outside filled with a special fluid called a refrigerant. This fluid can change back and forth between liquid and gas. As it changes, it absorbs or releases heat, so it is used to “carry” heat from one place to another, such as from the inside of the refrigerator to the outside.
And the process gets quite a bit more complicated with all the controls and valves involved. But its effect is remarkable. An air conditioner takes heat from a cooler place and dumps it in a warmer place, seemingly working against the laws of physics. What drives the process, of course, is electricity — quite a lot of it, in fact.
Central Air Conditioners and Heat Pumps
Central air conditioners and heat pumps are designed to cool the entire house. In each system, a large compressor unit located outside drives the process; an indoor coil filled with refrigerant cools air that is then distributed throughout the house via ducts. Heat pumps are like central air conditioners, except that the cycle can be reversed and used for heating during the winter months. (Heat pumps are described in more detail in the heating section.) With a central air conditioner, the same duct system is used with a furnace for forced warm-air heating. In fact, the central air conditioner typically uses the furnace fan to distribute air to the ducts.
Air conditioners and heat pumps use the refrigerant cycle to transfer heat between an inside unit and an outside uint. Heat pumps differ from air conditioners only in the special valve that allows the cycle to reverse, providing either warm or cool air to the inside.
Room Air Conditioners
Room air conditioners are available for mounting in windows or through walls, but in each case they work the same way, with the compressor located outside. Room air conditioners are sized to cool just one room, so a number of them may be required for a whole house. Individual units cost less to buy than central systems.
Evaporative Coolers
Evaporative coolers, sometimes called swamp coolers, are less common than vapor compression (refrigerant) air conditioners, but they are a practical alternative in very dry areas, such as the Southwest. They work by pulling fresh outside air through moist pads where the air is cooled by evaporation. The cooler air is then circulated through a house. This process is very similar to the experience of feeling cold when you get out of a swimming pool in the breeze. An evaporative cooler can lower the temperature of outside air by as much as 30 degrees.
They can save as much as 75% on cooling costs during the summer because the only mechanical component that uses electricity is the fan. Plus, because the technology is simpler, it can also cost much less to purchase than a central air conditioner — often about half.
A direct evaporative cooler adds moisture to a house, which could be considered a benefit in very dry climates. An indirect evaporative cooler is a little different in that the evaporation of water takes place on one side of a heat exchanger. House air is forced across the other side of the heat exchanger where it cools off but does not pick up moisture. Both types begin to lose their effectiveness with increasing humidity, because humid air is less able to carry additional moisture.
For evaporative coolers to do their job, they must be the right size. The cooling capacity of an evaporative cooler is measured not in the amount of heat it can remove (Btu), but in the fan pressure required to circulate the cool air throughout the house, in cubic feet per minute (cfm). A good rule is to figure the cubic square footage of your house and divide by 2. For example, a 1,500-square-foot house with 8-foot-high ceilings would require a 6,000 cfm cooler.
Ductless Mini-Split Air Conditioners
Mini-split systems, very popular in other countries, can be an attractive retrofit option for room additions and for houses without ductwork, such as those using hydronic heat (see the heating section). Like conventional central air conditioners, mini-splits use an outside compressor/condenser and indoor air handling units. The difference is that each room or zone to be cooled has its own air handler. Each indoor unit is connected to the outdoor unit via a conduit carrying the power and refrigerant lines. Indoor units are typically mounted on the wall or ceiling.
The major advantage of a ductless mini-split is its flexibility in cooling individual rooms or zones. By providing dedicated units to each space, it is easier to meet the varying comfort needs of different rooms.
By avoiding the use of ductwork, ductless mini-splits also avoid energy losses associated with central forced-air systems.
The primary disadvantage of mini-splits is cost. They cost much more than a typical central air conditioner of the same size, where ductwork is already in place. But, when considering the cost and energy losses associated with installing new ductwork for a central air conditioner, buying a ductless mini-split may not be such a bad deal, especially considering the long-term energy savings. Talk with your contractor about what option would be most cost-effective for you.
www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40
