filter driers etiketine sahip kayıtlar gösteriliyor. Tüm kayıtları göster
filter driers etiketine sahip kayıtlar gösteriliyor. Tüm kayıtları göster

6 Temmuz 2018 Cuma

Compressor Types

Compressor Types

Two types of compressor dominate HVAC systems in buildings: piston and scroll.
The piston type uses pistons attached to a motor-driven crankshaft to draw in and compress the refrigerant.

Scroll compressors use an orbiting scroll on an eccentric motor-driven crankshaft to suck in vaporized refrigerant and push it into a stationary scroll whose volume gradually decreases to compress the refrigerant. There are three forms of compressor construction. Hermetically sealed units have motor and compressor sealed within a welded steel casing. They can't leak, but they also can't be repaired. Semi-hermetic units put motor and compressor inside a steel shell whose halves are sealed with a gasket and bolts. These can be opened for repairs, but might leak refrigerant. Open compressors have motor and compressor as separate units linked by a coupling. This variety is found in very large HVAC systems.
www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

Refrigerant Leak Detection

Refrigerant Leak Detection
Leak detection is an essential service practice. There are many old and new methods available to assist technicians' eyes and ears in finding leak sites.
All pressurized HVACR systems can eventually leak refrigerant. Therefore, it's the responsibility of the HVACR technician to monitor systems regularly and inspect for leaks.
Although a tight system — with minimal leakage that doesn't affect system performance — may not pose a problem, a more serious leak will do so, and could occur at any time.
Some leaks are plainly visible to the eye. These include a visible line break, the presence of oil, and quite possibly a refrigerant vapor cloud of escaping gas.
An audible leak might also be detected if a system is pressurized and large leaks are present.


www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

5 Temmuz 2018 Perşembe

HVAC Components

HVAC Components
Other important components of an HVAC system include:
Ductwork: This system of metal pathways allows for distribution of hot or cold air throughout your home.
Humidifier: Adds moisture back into the air before distribution throughout the home, ultimately making breathing easier.
Thermostat: This is what allows you to control the temperature in your home.
Filters: Ensures air in your home is free of dirt, allergens, and odors, and helps maintain your system.
In order to ensure that all aspects of your home’s HVAC system are running at peak performance, it is essential to perform seasonal and annual maintenance. Keeping filters and ducts clean of dust and debris helps make your system more efficient. It also ensures your HVAC systems keeps your family comfortable for many years.


www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

Heating systems

Heating systems

Heating systems can take a couple of different forms. Some are furnaces that burn material to provide heated air through the ductwork, while another popular choice is boilers that heat water for steam radiators, or forced-water systems with baseboard radiators, electric heat, and heat pumps. A furnace will generally operate on natural gas or propane, while a boiler will use gas or oil to heat the water.

Another option is a radiant floor, also known as a hydronic heating system. These use piping under a floor, and are made up of flexible tubes that are filled with water or a glycol solution. These can heat any kind of floor, including concrete, and are an efficient method of providing warmth in a home. They can even be retrofitted into wooden flooring, though they need to be carefully installed in sheathing for wooden floors.

www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

Dıffeent Types Of Hvac Systems

Dıffeent Types Of Hvac Systems

For most people, heating and cooling will account for as much as half of the energy they use. With this in mind, it’s important to choose a HVAC system that will meet your comfort needs, without drawing on excess power and escalating your cost of living.
• People living in hot or cold climates might go for a single stage system, designed to produce just heating or cooling. These tend to be inexpensive, but are also rather inefficient and will typically be working at capacity even when it’s not required.
• More advanced models will offer variable fan speeds to cut down on power use, however they remain inefficient when compared to multi-stage systems, and are thus more expensive to run over the long term.
• Zoned systems, on the other hand, have been designed to heat or cool individual parts of your home. This is done by designing zone valves and dampers inside the vents and ductwork that selectively block the flow of air. For people with larger properties this is of immeasurable value as it prevents the system from heating or cooling areas in the home that are not in use.
• HVAC systems can also be built to offer humidity control, and both humidifiers and dehumidifiers can be added as options to heating and cooling systems. People that live in very dry environments or the tropics find these additions to the system essential. With that being said, some people prefer to install separate humidifier or dehumidifier systems, so that they can manage the humidity of their environment without also having to turn on the air conditioner.



www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

Function of Condenser


Function of Condenser
In a cooling cycle of a refrigeration system, heat is absorbed by the vapor refrigerant in the evaporator followed by the compression of the refrigerant by the compressor. The high pressure and high temperature state of the vapor refrigerant is then converted to liquid at the cond. It is designed to condense effectively the compressed refrigerant vapor.
There are basically three types of condensing unit depending on how the heat is removed by the condensing medium which is usually water, air or a combination of both.
  • Air-Cooled types are usually used in the residential and small offices applications. They are used in small capacity systems below 20 tons. The advantages of using this design include not having to do water piping, not necessary to have water disposal system, saving in water costs and not much scaling problems caused by the mineral content of the water. It is also easier to install and has lower initial cost. There isn't much maintenance problems. The disadvantages are that it requires higher power per ton of refrigeration, has shorter compressor life and on days when most cooling is required, the least is available. 

  • The circulation of air-cooled type can be by natural convection or by forced convection (usually using blower or fan). Due to its limited capacity, natural convection is used in smaller applications such as freezers and refrigerators. In forced convection, air is circulated by using a fan or blower that pulls the atmospheric air through the finned coils. Internally, the refrigerant circulates through the coil and air flows across the outside of the tubes.
  • Water-Cooled There are 3 types commonly being used. They are shell and tube, shell and coil, and double tube. The most commonly used is the shell and tube type and are usually available from two tons up to couple of hundred tons. This design has lower power requirements per ton of refrigeration and the compressors can last longer compared to the air-cooled type. A water cooling tower is frequently used for higher capacity application.
  • Evaporative type which is a combination of water and air-cooled.
Air-Cooled and Water-Cooled Comparison Summary
  • Air-cooled type operates at higher head pressure or condensing pressure, hence reducing the capacity of the compressor and increases the power intake. In general, a 2 hp water-cooled system will require the same refrigeration as a 3 hp air-cooled system.
  • The maintenance costs of water-cooled type is about three to four times the air-cooled type. Air-cooled type maintenance is usually limited to regular lubrication of fan and motor bearings. Water-cooled type requires cleaning from algae and bacteria. Scales on the tubes are removed by using acid compound. Proper water treatment is also critical to the operation of the cond.
www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

4 Temmuz 2018 Çarşamba

Types of Filter

Types of Filter
There are basically two types in used today.
• Liquid Line Type
• Suction Line Type

Liquid Line Type is placed after the condenser coil and before the expansion valve. The liquid refrigerant that flows from the condenser to the expansion valve is filtered from particles and moisture before entering it. Good filter will filter out particles that are 20 micron or above from the system.
Some higher end device has sight glass that enables the technician to look into it to see the level of refrigerant. Some have chemical in it that indicate the amount of moisture in the system based on the color of it.
Suction Line Type is placed after the evaporator and before the compressor. This device is used to protect the compressor especially after any failure that contaminates the system.
Motor failure in the compressor usually cause acid and other contaminants to be introduced into the refrigerant system hence it is important to have the suction line filter dryer installed.


www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

Filter Driers

Filter Driers

Filter driers are devices used in a HVAC system that are a combination of filter and dryer (or drier). A filter is used to remove any particle such as dirt, metal or chips from entering the refrigerant flow control. The refrigerant flow control device could be thermostatic expansion valve or simply a capillary tube.
The filter is sometimes also referred to as a strainer. It is critical that these particles are filtered out and prevented from going into the metering device. It can cause blockage to the passage flow of the refrigerant in the expansion valve and cause improper operation to the system.
A drier as its name imply is used to remove the moisture from the refrigerant. Sometimes it is also referred to as dehydrator or dryer. It is necessary to remove moisture from the system otherwise it may freeze inside the tube causing the flow of refrigerant to be restricted. The moisture will also cause the formation of acids and sludge when in contact with oil in the system.

These devices are usually used in bigger system where the refrigerant circuit is designed for field service. Residential units that are charged with refrigerant at factory level and hermetically sealed do not use these devices as the possibility of moisture and particles entering the system is minimal.


www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40