cooling units etiketine sahip kayıtlar gösteriliyor. Tüm kayıtları göster
cooling units etiketine sahip kayıtlar gösteriliyor. Tüm kayıtları göster

9 Temmuz 2018 Pazartesi

CHILLED SYSTEM

CHILLED  SYSTEM

Water cooled chillers: With water cooled chillers, the refrigerant is cooled with a shell and tube condenser that is part of the chiller package. The condenser water heat is then rejected to the cooling tower located outdoors.
Glycol cooled chillers: Glycol-cooled chillers look identical to the water-cooled chillers. With glycol-cooled chillers, heat removed from the returning chilled water is rejected to a glycol loop for transport to the outside atmosphere. The glycol flows via pipes to an outdoor-mounted device called a dry cooler also known as a fluid cooler. Heat is rejected to the outside atmosphere as fans force outdoor air through the warm glycol-filled coil in the dry cooler.
 Air cooled chillers: With air-cooled chillers, the heat of refrigerant is rejected to an air-cooled condenser that is typically integrated with the chiller. This type of chiller is known as a packaged chiller and can also be integrated into a cooling facility module. Air-cooled chillers are typically located outdoors.



www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

HVAC COOLING SYSTEM DESIGN


HVAC COOLING SYSTEM DESIGN
 Cooling and heat dissipation techniques are extremely important topics when it comes to designing and operating a data center. In many instances, system designs fall short of clients’ expectations in terms of reliability and availability. Perhaps naively, often too much importance is placed on the power and network availability without the same being applied to the air conditioning systems.
 Remember, ‘a chain is only as strong as its weakest link’. Infrastructure designs often fail to meet expectations because the same level of reliability/redundancy in many instances is not applied to all other components of the supporting infrastructure. While many people understand that only a short interruption in power supply to computer equipment can mean loss of data, what is often not considered is that an interruption in cooling system can be just as devastating.
This section includes:
1. Heat gains
2. Temperature and humidity requirements
3. Ventilation rates
4. Air quality
5. Cooling loads
6. HVAC equipment


www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

Central Heating Systems


Central Heating Systems
Central heating systems have been considered a necessity in our homes and businesses for many years. When comparing available systems, consumers should carefully consider safety, installation cost, operating costs, maintenance costs, and comfort.
Types of Heating Systems
There are two basic types of systems - those that require a flame to operate (i.e., combustion based), and those that do not. Most central systems presently installed create heat by combustion, just as they did in the early part of the century. These systems use a furnace to burn a fossil fuel (such as oil, natural gas or propane) or, in some instances, wood. More advanced, non-combustion systems operate by transferring or moving heat from one location to another.
Combustion Based Systems
Until the last few years, combustion-based systems have been the preferred heating systems for home and business owners because of their moderate installation and operating costs, and wide availability in the market place. Unfortunately, there are a number of serious safety and related maintenance concerns with these systems.
Some combustion-based systems present an explosion hazard if the storage or delivery of their fuel is not carefully controlled. Explosions due to improperly installed or maintained gas pipes and delivery systems are often in the news. Since these systems require a flame to operate, failures or improper installation of system components (for example, heat exchanger, damper, chimney, or flue) can result in property loss to fire. Fortunately, smoke detectors have saved many lives that might have been lost to fires caused by combustion-based heating systems.
In addition to heat, combustion-based heating systems also create by-products such as carbon monoxide. Carbon monoxide is a result of the incomplete burning of fuel in combustion-based systems. Incorrectly installed systems, chimneys that are blocked by birds nests, or downdrafting can cause carbon monoxide to remain inside of buildings. This is especially dangerous in modern, well-sealed buildings, where it is difficult for outside combustion air to reach the furnace, and where carbon monoxide can be trapped and build up over time. Furnaces, water heaters, and other appliances must be properly vented outside.
Combustion-based systems that deliver heat through ducts present occasional "blasts" of hot air. This not only reduces comfort directly, but tends to dehumidify the air. The addition of a central humidifier (with its associated installation, operating, and maintenance costs) can correct this humidity problem.
Combustion based central heating systems are often coupled with low-efficiency central air conditioners. This raises installation and operating costs significantly, while adding an entirely separate unit to be maintained.
Heat Transfer Systems
Non-combustion or heat transfer systems include heat pumps and geoexchange systems. Heat pumps operate by capturing heat from outdoor air and transferring it inside of a home or business. geoexchange systems capture and transfer heat from the earth.
Nearly all heat transfer systems can be reversed, providing central cooling as well as heating. Some heat pumps and most geoexchange systems also provide domestic hot water at low operating costs.
Heat Pumps
Beginning in the 1970s, air-source heat pumps came into common use. They have the advantage of no combustion, and thus no possibility of indoor pollutants like carbon monoxide. Heat pumps provide central air conditioning as well as heating as a matter of course. And they are installation-cost competitive with a central combustion furnace/central air conditioner combination.
Heat pumps operate by moving or transferring heat, rather than creating it. During the summer, a heat pump captures heat from inside a home or business and transfers it to the outdoor air through a condensing unit. During the winter, the process is reversed. Heat is captured from outdoor air, compressed, and released inside.
Much less electricity is used to move heat rather than create it, making heat pumps more economical than resistance heating. However, in all but the most moderate climates, the heating ability of the heat pump is limited by freezing outdoor temperatures. So electric resistance heat is used to supplement outdoor-air-source heat pump during the coldest weather, preventing "cold blow."
Depending on climate, air-source heat pumps (including their supplementary resistance heat) are about 1.5 to 3 times more efficient than resistance heating alone. Operating efficiency has improved since the 70s, making their operating cost generally competitive with combustion-based systems, depending on local fuel prices. With their outdoor unit subject to weathering, some maintenance should be expected.
www.bilkargroup.com

www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

Selecting Heating and Cooling Systems


Selecting Heating and Cooling Systems

Heating and cooling system selection is very important to a home. Read on for some tips in selecting the right one for your needs.

 This is a very important decision with many variables. These systems are components to a building that will last for a long time and can be costly. They play a big part in a house's energy efficiency and comfort level. There is not a "one size fits all" answer; it will depend on the region of the country a home is built in, the homeowners' budget and individual preferences. Every heating and cooling system has pros and cons. Here are some things to think about:

- Forced Air Styles: The new technology utilized in forced air units is much more efficient than in the past. They can be run from a variety of energy sources such as gas, electric, oil and propane. A downside is that they may produce spotty heat and coolness. Those that are equipped with blowers may expose allergy sufferers to more dust.
- Heat Pumps: Heat pumps are quite efficient in terms of energy use. Both the AC and the warmth can be piped through the same ventilation pathways, cutting down on installation costs. Some of these units are split into inside/outside locations. Filters which trap debris from vents must be changed every month or a breakdown in the system could occur.
- Duct-free: Systems that are duct-free are those that either hang from the wall or set on the floor. A positive of this type of unit is that it costs less in terms of installation as there are no ducts to position. The duct-free devices are best used in small areas or temperate climates. If temperatures drop well into the freezing zones, these models won't provide enough warmth in the home.

- Radiators with Steam: These are also called boilers and can be comfortable because they emit moisture along with heat. Some downsides include that they can rattle, clank, make lots of noise and the warmth may be spotty through the home. This is kind of an old-fashioned method of warming up one's abode, but it may make a comeback.

- Solar Energy: Solar technology is great for energy efficiency because it harnesses warmth from the sun. Solar systems can be passive or active. Panels on the roof or thermal mass holders are options.

- Wind Energy: Harnessing the power of the wind may also be an ecologically sound method of using natural sources of energy.

- Radiant Heaters: These devices are installed beneath the flooring of one room or an entire house. Pipes with hot water warm surfaces. No ductwork is requiredPsychology Articles, so no allergens will blow around. Efficiency is quite high.

There are many options in heating and cooling systems. Each of their goals is to provide comfortable temperatures inside of a home with as low a utility consumption as possible.


www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

6 Temmuz 2018 Cuma

Condenser, Evaporator, and Compressor

Condenser, Evaporator, and Compressor

The condenser is one of three primary elements in your air conditioning system. The other two, the evaporator and compressor, are also important. To understand how the condenser works, it’s important to understand the other two as well.

• Evaporator: The system starts in home with inside air being blown over evaporator coils. These coils contain low-pressure refrigerant which absorbs the heat from the air and converts into a high-pressure gas.
• Compressor: The gas is transferred into the compressor, which is in the outside unit. Here, it’s compressed to help convert it back into a liquid so it can continue the cooling cycle. This produces extra heat.
• Condenser: The condenser is a set of coils, also located inside the outdoor unit. Here, a fan blows across the coils, dissipating the heat from the refrigerant inside them and allowing it to convert back into a liquid, at which point it’s sent back inside to start the process over again.

Without the condenser, the refrigerant would retain its heat and the process would not work. Therefore, it’s important to be able to tell if the condenser is malfunctioning or broken.


Diagnosing Condenser Problems

Often, the problem may not be with the condenser coils themselves, but with the fan or motor in the outdoor unit. The following signs can let you know if the condenser is broken:

• Air conditioner blows warm air inside.
• Outdoor condenser fan doesn’t run.
• Refrigerant leaks from outdoor unit.

Compressor Types

Compressor Types

Two types of compressor dominate HVAC systems in buildings: piston and scroll.
The piston type uses pistons attached to a motor-driven crankshaft to draw in and compress the refrigerant.

Scroll compressors use an orbiting scroll on an eccentric motor-driven crankshaft to suck in vaporized refrigerant and push it into a stationary scroll whose volume gradually decreases to compress the refrigerant. There are three forms of compressor construction. Hermetically sealed units have motor and compressor sealed within a welded steel casing. They can't leak, but they also can't be repaired. Semi-hermetic units put motor and compressor inside a steel shell whose halves are sealed with a gasket and bolts. These can be opened for repairs, but might leak refrigerant. Open compressors have motor and compressor as separate units linked by a coupling. This variety is found in very large HVAC systems.
www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

What Is the Function of a Compressor in an HVAC System?

What Is the Function of a Compressor in an HVAC System?

The compressor is the heart of the cooling function of heating, ventilation and air conditioning (HVAC) systems. The air conditioner component of a building's HVAC system essentially is a type of refrigerator that cools and dehumidifies the air in the building, ensuring thermal comfort for the occupants. Most HVAC compressors look like a black box with lines running to and from it.

Compressor Function
Air conditioners are devices that transfer heat from an enclosed space to the outside air. The motor-driven compressor in an air conditioning system powers the whole heat-transfer cycle. Air conditioners rely on two facts of nature. One is that heat flows from a high-temperature area to a lower temperature area. The other is that gases always flow from a high-pressure area to a low-pressure area.
Air Conditioning Cycle
The heat-transfer cycle starts as the compressor squeezes the refrigerant. This squeezing action raises its temperature well above that of the surrounding atmosphere. The squeezing action also pressurizes the refrigerant just to its liquefying point so it can flow through the system. The hot, pressurized, liquified refrigerant flows to a condenser coil where it gives up its excess heat to the cooler atmosphere. Typically, a fan blows air through the condenser coil to facilitate transfer of the excess heat.
Expansion Phase
After shedding its excess heat to the atmosphere, the refrigerant flows to an evaporator coil where it expands into a gas at the reduced pressure in the evaporator, which is located in the space to be cooled. This expansion requires heat, which is drawn from the air in the enclosed space that's being cooled. This warms the refrigerant. The cold evaporator also draws humidity from the air. A fan blowing across the evaporator coil facilitates this transfer of heat and humidity. As the compressor pushes hot pressurized refrigerant toward the condenser, it pulls the warm vaporized refrigerant from the evaporator to start the cycle all over again.

www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40



+90 553 343 50 40

What does the Expansion Valve do in an Air Conditioning System

What does the Expansion Valve do in an Air Conditioning System
The modern air conditioner is quite a marvel of engineering. The complex working of its components is the reason that only professionals can effectively diagnose and repair a malfunctioning air conditioner.
One of the key components allowing an air conditioner to work is a part called the expansion valve. Without this valve, an AC would not be able to draw sufficient heat from the inside of a home.

How the expansion valve helps cool down your home
In order to explain the purpose of an expansion valve requires first explaining the basics of how refrigerant works in an air conditioner. Refrigerant is a heat transference fluid that shifts between liquid and gaseous state, absorbing and releasing heat as it does so. When the refrigerant moves through the outdoor condenser coil, it releases heat to the outside. Cooled down, it then moves toward the indoor evaporator where it absorbs heat.
However, at the point after leaving the condenser, the refrigerant—which is in a high-pressure liquid form—is still too hot to effectively go carry out the process of evaporation that will draw heat out of the indoor air. This is where the expansion valve does its job: the valve is designed to remove pressure from the refrigerant and rapidly cool it down into a cold gas. The valve doesn’t remove heat, only pressure—but removing the pressure has the effect of lowering the temperature of the refrigerant. After it leaves the valve, the refrigerant will be at its the coldest. The refrigerant is now ready to move through the indoor evaporator coil, where it will meet warm indoor air and through evaporation lower the temperature of the air.
Live any component inside an air conditioning system, the expansion valve can malfunction, leading to an AC that won’t provide any cooling. Always call on professionals to look your air conditioner when it encounters trouble: a number of different malfunctions might lurk behind the problem, and it takes training to locate the actual cause. If a broken expansion valve is at fault, the technician will repair or replace it.


www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

Classification of Valves

Classification of Valves

Fluid control valves are classified in many ways. Following is the classification of valves.


Multi Turn and Quarter Turn Valves

Multi turn valves need many turns of actuator to bring closure member (disc) from fully open position to fully closed position. Examples of multi turn valves are gate valves, globe valves, needle valves, and diaphragm and pinch valves.
While quarter turn valves need only quarter ,0 to 900 degree, motion of closure member (disc) to bring it from full open position to full closed position.  Examples of quarter turn valves are butterfly valves, ball vales and plug valves etc. Quarter turn vales are quickopening valves.

Self actuated Valves

Self actuated valves don’t need actuator to operate them. These valves operate based on some property of fluid line like pressure or flow. Self actuated valves don’t need operator’s interference to control the fluid. Examples of self actuated valves are check valves and pressure relief valves or safety valves.

Linear Motion and Rotary Motion Valves

In linear motion valves, disc moves in linear or straight path to open, close or throttle the flow in valve. While in Rotary motion valves, disc rotates to open, close or throttle the flow. Examples of linear motion valves are gate valves, needle valves, globe valves, diaphragm valves and pinch valves. Examples of Rotary motion valves are ball valves, butterfly valves etc.


General Types of valves

In general following are the types of valves.
• Gate valve
• Globe Valve
• Pinch Valve
• Needle valve
• Diaphragm valve
• Ball valve
• Butterfly Valve
• Check valve
• Pressure relief Valve (safety or relief valve)

www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40



+90 553 343 50 40

Types of Heat Exchangers used in Hvac system

Types of Heat Exchangers used in Hvac system
Heat exchangers are essential part of any kind of HVAC system nowadays. Heat exchangers contribute substantially towards energy conservation and reduction in energy bills.So what are the different types of heat exchangers that a HVAC system can use? 
The main function of a heat recovery system is to increase the energy efficiency by reducing energy consumption and also by reducing the cost of operating by transferring heat between two gases or fluids, thus reducing the energy bills.
The heat exchangers are the best known devices for this purpose. In heat exchangers, as the name suggests, there is a transfer of energy from one fluid to another. Both these fluids are physically separated and there is no direct contact between the fluids. There are different types of heat exchangers such as shell and tube, U tube, shell and coil, helical, plate etc. The transfer of heat can be between steam and water, water and steam, refrigerant and water, refrigerant and air, water and water. Now let’s take a look as to what are the different types of heat exchangers.

Rotary wheel type heat exchanger
A rotary wheel type heat exchanger has a large surface cylinder which is attached to the shaft. It has got a gas permeable material inside it. When the cylinder rotates, both the gases move in a counter flow pattern axially to the shaft. The heat from the warm gas is absorbed by the gas permeable material and then it is transferred to the colder gas. Sometimes hygroscopic material is put on the gas permeable material to absorb the moisture from the gases. Thus the moist gas becomes dry and transfers the moisture to the dry gas. Both latent and sensible heat is transferred in this system.
Fixed Plate heat exchangers
These types of heat exchangers do not have any moving parts. They have fixed plates that are alternately arranged and are separate from each other. Both the gases and fluids flow separately in these alternate plates and the transfer of heat takes place between them. The flow can be counter flow, parallel flow or cross flow.
Heat pipe exchangers.
This type of heat exchanger has an evaporator and a condenser separated by a plate. It has tubes running parallel and separated from each other. On the evaporator side the hot air transfers its energy to the liquid refrigerant and thus boiling it. The vapor refrigerant now passes through the pipes to the condenser side. The opposite process takes place. The cold air now passes over the vapor refrigerant. The vapor refrigerant after transferring its energy turns to liquid and flows though the pipes to the evaporator side. This type of heat exchanger generally uses parallel flow patterns.
Run- around system
In this type of system, a pump circulates water or any other liquid through the system. There are coils that are mounted in either series or parallel to facilitate maximum amount of heat transfer. This type of system is beneficial in any season. This means that if the outside air is warmer than the exhaust air, the exhaust air pre cools outside air. And if the outside air is cooler than the exhaust air, the exhaust air pre heats the outside air, making the system more and more energy efficient.
Hot gas heat exchanger
The HVAC system’s compressor generates heat by compressing refrigerant. This heat can be captured and used for heating domestic water. For this purpose a heat exchanger is placed in between the compressor and the condenser. The water that is to be heated is circulated though this heat exchanger with the help of a pump whenever the HVAC system is on.
Double bundle condenser heat exchanger
This heat exchanger consists of two sets of water tubes in the condenser shell. The superheated gas is forced into the shell where the transfer of heat to the water takes place through the tubes.
Heat jackets
Water jackets are kept at the sides of a reciprocating engine or a gas turbine to absorb the heat generated. This heat can be used for generating steam or for heating water or fuel oil.
Hot flue gas heat exchangers
The hot flue gases from the boiler exhaust can be used to heat water or fuel oil. An arrangement consisting of a series of pipes or water jackets are made in the boiler exhaust for the transfer of the heat. It can mainly be used to preheat the boiler feed water.
Hot drain heat exchangers
Heat from the hot condensate used in the kitchen, bathrooms or laundry system can be used for boiling water.Condensate is continuously formed when the release of heat takes place. A heat exchanger placed in the condensate return can take the condensate heat for heating water.
Heat pump water heater
The atmosphere of kitchens and laundries is extremely hot. This heat can be used to heat water or for other purposes. This can be done by using a dedicated heat pump that mechanically concentrates the heat in the atmosphere and bring it to the temperature where it can be used.
www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

Types of compressors

Types of compressors
The compressor is the component at the heart of a refrigerant circuit based on the so called “vapour compression cycle”.

This thermodynamic cycle exploits the evaporation of a refrigerant inside a closed loop piping circuit.
Specifically, evaporation occurs in a heat exchanger called the evaporator, which absorbs energy from the surrounding air; this is then delivered to the food storage compartment or air-conditioned space by natural or fan-forced convection.
The same also applies when using water as the medium, which is pumped through the heat exchanger and then flows into the storage tank for use by the terminal units.
Once having evaporated, the refrigerant can no longer absorb considerable amounts of energy, and consequently it needs to be returned to the liquid state by condensation.
The problem thus arises of having an environment that’s “cold” enough to absorb energy from the refrigerant, which naturally cannot be the same compartment or space that’s just been cooled.
The compressor is then used to compress the refrigerant to a pressure that’s higher than in the evaporator (up to 8-10 times!) so that the condensation process can take place at a temperature that’s compatible with a readily available “cold” source, typically the outside air.
Condensation thus occurs at a high temperature (usually 35-55°C) inside a heat exchanger where the two fluids are outside air and refrigerant. The latter condenses and returns to the liquid state, while the outside air will be heated. The liquid refrigerant is still at high pressure when it leaves the condenser. An expansion device is thus needed to expand the liquid refrigerant and reduce its pressure to the value at which evaporation occurs. The refrigerant has now returned to its initial state (liquid at low pressure and temperature) and can once again absorb energy from the air or water.

www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

Refrigerant Leak Detection

Refrigerant Leak Detection
Leak detection is an essential service practice. There are many old and new methods available to assist technicians' eyes and ears in finding leak sites.
All pressurized HVACR systems can eventually leak refrigerant. Therefore, it's the responsibility of the HVACR technician to monitor systems regularly and inspect for leaks.
Although a tight system — with minimal leakage that doesn't affect system performance — may not pose a problem, a more serious leak will do so, and could occur at any time.
Some leaks are plainly visible to the eye. These include a visible line break, the presence of oil, and quite possibly a refrigerant vapor cloud of escaping gas.
An audible leak might also be detected if a system is pressurized and large leaks are present.


www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

5 Temmuz 2018 Perşembe

How Hvac Systems Work


How Hvac Systems Work
The following diagram illustrates the basic function of a HVAC system:


•          The building automation device (computer or wall-mounted gadgets usually) can be used to determine whether to heat or cool the space, and to what temperature
•          The system then either heats or cools the coils inside
•          When air brought in from the outside is pushed through these coils, it is either heated or cooled before being pushed into the living space
•          At the same time, air will be displaced from the room back into the system.
Smaller air conditioning systems may operate in the reverse, however, where they collect heat from within a space and push it out in order to cool a room down. We can see these kinds of systems in places like cars. Here’s how these types of HVAC systems work:


This diagram reveals how a system will collect heat from within a space, soak it up like a sponge, and push it back out into the air.
There are five key parts in this system that allow it to operate:
•          Expansion valve: This device creates a restriction in the liquid line of a system, which in turn creates a pressure drop.
•          Evaporator: This device is what removes heat from the space by exchanging it for a boiling refrigerant.
•          Compressor: Think of this component as the system’s heartbeat - it creates the energy and thrust to move refrigerant around the system.
•          Condenser: This is the device that pushes the heat that has built up inside the refrigerant into the outside air.
•          Receiver drier: In order to preserve the air quality, this storage area for excess refrigerant contains a drying agent and a filter that removes contaminants from the system.

www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

Cooling systems

Cooling systems
Air conditioners come in many forms, from the massive boxes designed to cool an entire house to a portable window-mounted box that can be pulled out and used in cooler climates to handle short summers.
Many air conditioners can even be installed by the owner, with ductless mini split systems a popular choice. Installation is still a major project, as the interior and exterior elements of the system need to be properly connected, but they are relatively inexpensive to buy and run.
For dryer climates, evaporative coolers are a popular choice. They draw outside air into the system, passing it through water-saturated pads, which cool and moisten the air before pushing it into the living space and displacing the hot air.


www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

Heating, Ventilating, and Air Conditioning

Heating, Ventilating, and Air Conditioning
HVAC stands for Heating, Ventilating, and Air Conditioning, and HVAC systems are, effectively, everything from your air conditioner at home to the large systems used in industrial complexes and apartment blocks. A good HVAC system aims to provide thermal control and indoor comfort, and one that is designed using the principles of thermodynamics, fluid mechanics, and heat transfer.
The big air conditioner boxes that you might see on top of apartment blocks or offices are examples of (the visible part of) HVAC systems. They’re typically deployed in large industrial buildings, skyscrapers, apartment blocks, and large interior environments. They’re also an essential component of environments where there are health regulations requiring that temperature and humidity be kept at certain levels, using air taken from outside.
But heating and cooling systems you use in your home are also HVAC systems. They may take a different form, but many of the fundamental principles determining how they operate, as well as their efficiency, crosses over from the smallest of personal devices right through to the biggest commercial installations.

www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

How Aır Curtaıns Reduce Coolıng Costs


How Aır Curtaıns Reduce Coolıng Costs
Nearly all business owners are wary of costs and search for effective ways to save money. In warmer months, most businesses turn their thermostats down and make use of air conditioning systems. Maintaining an optimum temperature is essential for ensuring that customers enter the building- and that they wish to stay there.
However, controlling the climate of premises can be a costly affair. Air curtains can reduce cooling costs by preventing the amount of warm air that enters through an entryway. They will also prevent the loss of cooled air, by blocking the entry of hot air when a door is opened and closed. Both of these features mean that you can maintain a desired temperature, without needing to use air conditioning as often, or for as lengthy periods of time. This reduces the amount of energy used by air conditioning units, therefore saving your business valuable money spent on cooling costs. Air curtains also prevent outside contaminants- such as dust and insects – from entering an establishment. This can be invaluable for customers or employees with sensitivity to these contaminants, and can be particularly useful in months where hay fever is prominent.

Air curtains come in a variety models. Most are designed to fit above eight foot doorways; however, many companies have created models to fit in smaller or larger gaps. Air curtain length can also vary- some need only to be a little shorter than the width of the doorway, whereas other companies find that extra-long curtains, or several in a row, have a greater impact. You also choose the right strength to fit the requirements of your company. For example, air curtains made for walk-in freezers must work harder to account for the drastic difference in temperatures. Businesses that work in dusty or bug infested areas may look for air curtains that are best at filtering such contaminants.
Whatever your needs, air curtains are certain to save you money on the costs of climate control, and may even bring you a greater return as customers are happy to stay on site longer.
www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

Filter Drier What is it and what does it do.

Filter Drier What is it and what does it do.
Filter driers are exactly what they sound like, they are filters. They filter the refrigerant inside the ac system. Filter driers need to be able to trap and contain moisture, acid, contaminants and wax from circulating throughout the air conditioner. Today's systems are very well designed, but problems can arise. HFC refrigerants by themselves will work for many years in a system, even when they are heated up above normal. However, under certain conditions HFC's can react and form acids. Moisture in the system can have a reaction with the refrigerants and cause hydrofluoric acid. These acids unchecked can cause havoc on your air conditioning system. Over time, pumping acid through the system will burn the insulation off the wires in the compressor. Once the wires have no more insulation, they will ark with the metal inside the compressor causing tripped breakers. We call this a grounded compressor and the only repair is a new one (very expensive). Another problem is the acid inside your air conditioner can eat away at every part or surface in the system, decomposing any surface. Over time, small pieces of parts can break free. These tiny pieces can circulate through the system, clogging capillary tubes, TXVs, or even the filter drier.

                A filter drier needs to be replaced anytime the air conditioners refrigeration system is worked on. When you replace a compressor, a TXV or any time the system is open to the atmosphere, change the filter. One way to tell if the filter is clogged is to take the temperature an inch before and an inch after the filter. If you have, more than a 3 degree F drop it has clogged and needs replaced. When in doubt change it out. Filter driers are lifesavers in some cases such as a compressor burnout. A compressor burnout is when the compressor becomes grounded and when it arks it actually burns the refrigerant. Burnt refrigerant usually will turn a darker color than normal sometimes black and may become wax like in extreme conditions. Just changing your AC compressor will not cut it. The only way to ensure the new compressor runs its full life is to install new filter driers and use acid away in the system. Acid away is a product used to remove acid from dirty systems. Some manufacturers say that a suction line filter drier does a better job of removing moisture from the system. That is because the moisture tends to condense in the cold suction line and is easily trapped by the suction line filter drier. However, a suction line drier is only used for clean up purposes, say after a burnout. Suction driers installed should be left for two days to remove moisture, wax, acid and small contaminants. A suction drier should never under any circumstances be left in a system for more than 3 days. As it will become restricted very fast. Yes, filter driers will cost you more to install. However, the price of not having one could be you buying a completely new system.
www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

4 Temmuz 2018 Çarşamba

Types of Filter

Types of Filter
There are basically two types in used today.
• Liquid Line Type
• Suction Line Type

Liquid Line Type is placed after the condenser coil and before the expansion valve. The liquid refrigerant that flows from the condenser to the expansion valve is filtered from particles and moisture before entering it. Good filter will filter out particles that are 20 micron or above from the system.
Some higher end device has sight glass that enables the technician to look into it to see the level of refrigerant. Some have chemical in it that indicate the amount of moisture in the system based on the color of it.
Suction Line Type is placed after the evaporator and before the compressor. This device is used to protect the compressor especially after any failure that contaminates the system.
Motor failure in the compressor usually cause acid and other contaminants to be introduced into the refrigerant system hence it is important to have the suction line filter dryer installed.


www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

Expansion Valve


Expansion Valve
The expansion valve removes pressure from the liquid refrigerant to allow expansion or change of state from a liquid to a vapor in the evaporator.
The high-pressure liquid refrigerant entering the expansion valve is quite warm. This may be verified by feeling the liquid line at its connection to the expansion valve. The liquid refrigerant leaving the expansion valve is quite cold. The orifice within the valve does not remove heat, but only reduces pres­sure. Heat molecules contained in the liquid refrigerant are thus allowed to spread as the refrigerant moves out of the orifice. Under a greatly reduced pressure the liquid refrigerant is at its coldest as it leaves the expansion valve and enters the evaporator.
Pressures at the inlet and outlet of the expansion valve will closely approximate gauge pressures at the inlet and outlet of the compressor in most systems. The similarity of pressures is caused by the closeness of the components to each other. The slight variation in pressure readings of a very few pounds is due to resistance, causing a pressure drop in the lines and coils of the evaporator and condenser.

Two types of valves are used on machine air conditioning systems:
  • Internally-equalized valve - most common
  • Externally-equalized valve special control
Internally-Equalized Expansion Valve
The refrigerant enters the inlet and screen as a high-pressure liquid. The refrigerant flow is restricted by a metered orifice through which it must pass.
As the refrigerant passes through this orifice, it changes from a high-pressure liquid to a low-pressure liquid (or passes from the high side to the low side of the system).
Let's review briefly what happens to the refrigerant as we change its pressure.
As a high-pressure liquid, the boiling point of the refrigerant has been raised in direct proportion to its pressure. This has concentrated its heat content into a small area, raising the temperature of the refrigerant higher than that of the air passing over the condenser. This heat will then transfer from the warmer refrigerant to the cooler air, which con­denses the refrigerant to a liquid.
The heat transferred into the air is called latent heat of condensation. Four pounds (1.8 kg) of refrigerant flowing per minute through the orifice will result in 12,000 Btu (12.7 MJ) per hour transferred, which is designated a one ton unit. Six pounds (2.7 kg) of flow per minute will result in 18,000 Btu (19.0 MJ) per hour, or a one and one-half ton unit.
Let's look at each valve in detail.
The refrigerant flow through the metered orifice is extreamly important, anything restricting the flow will affect the entire system.
  • If the area cooled by the evaporator suddenly gets colder, the heat transfer requirements change. If the expansion valve continued to feed the same amount of refrigerant to the evaporator, the fins and coils would get colder until they eventually freeze over with ice and the air flow is stopped.
  • A thermal bulb has a small line filled with C02 is attached to the evaporator tailpipe. If the temperature on the tail pipe raises, the gas will expand and cause pressure against the diaphram. This expansion will then move the seat away from the orifice, allowing an increased refrigerant flow. As the tail pipe temperature drops, the pressure in the thermal bulb also drops, allowing the valve to restrict flow as required by the evaporator.
  • The pressure of the refrigerant entering the evaporator is fed back to the underside of the diaphragm through the internal equalizing passage. Expansion of the gas in the thermal bulb must overcome the internal balancing pressure before the valve will open to increase refrigerant flow.
  • A spring is installed against the valve and adjusted to a predetermined setting at the time of manufac­ture. This is the superheat spring which prevents slugging of the evaporator with excessive liquid.
  • Superheat is an increase in temperature of the gaseous refrigerant above the temperature at which the refrigerant vaporizes. The expansion valve is designed so that the temperature of the refrigerant at the evaporator outlet must have 8 to 12°F (4 to 7°C) of superheat before more refrigerant is allowed to enter the evaporator.
  • The adjusted tension of this spring is the determining factor in the opening and closing of the expansion valve. During opening or closing, the spring tension retards or assists valve operation as required. 
    • Normally, this spring is never adjusted in the field. Tension is adjusted from four to sixteen degrees as required for the unit on which it is to be installed. This original setting is sufficient for the life of the valve, and special equipment is required in most cases to accurately calibrate this adjustment
Externally-Equalized Expansion Valve
Operation of the externally-equalized valve is the same as the internal type except that evaporator pressure is fed against the underside of the diaphragm from the tail pipe of the evaporator by an equalizer line. This balances the temperature of the tail pipe through the expansion valve thermal bulb against the evaporator pressure taken from the tail pipe.

www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40

Expansion Valves


Expansion Valves
Expansion valves are devices used to control the refrigerant flow in a refrigeration system. They help to facilitate the change of higher pressure of liquid refrigerant in the condensing unit to lower pressure gas refrigerant in the evaporator.
The term "low side" is used to indicate the part of the system that operates under low pressure, in this case the evaporator. The "high side" is used to indicate the part of the system that operates under high pressure, in this case the condenser.
Types of Expansion Valves
There are basically four types of valves that are in used. These valves are also refer to as metering devices.
  • Automatic Exp. Valves
  • Thermostatic Exp. Valves
  • Capillary Tubes
  • Float Valves
Automatic Expansion Valve regulates the flow of refrigerant from the liquid line to the evaporator by using a pressure-actuated diaphragm. It maintains a constant pressure in the evaporator.
The setback is that it is not efficient if the load fluctuates hence this type is not suitable for use in air conditioning as the load fluctuates a lot during its operation.
Thermostatic Expansion Valve uses a valve mechanism to control the flow of liquid refrigerant into the evaporator coil. The flow is controlled by the pressure in the evaporator.
This type of metering device is able to operate well when the load fluctuates and hence is suitable for use in air conditioning system. When the evaporator warms, the valve provides a higher flow rate amd when it cools, it reduces the flow rate.
It is also commonly refer to as TXV, TEV or TX valve. There is a sensing bulb which detects the temperature of the coil and is usually located at a higher temperature within the evaporator.
The bulb must be clamped firmly to the coil to ensure proper sensing. When the temperature of the evaporator increases due to the demand for cooling, the pressure in the bulb will also increase hence pushing the spring to open the valve.
Similarly, when the temperature of the evaporator reduces due to a lack of demand for cooling, the pressure in the bulb will drop hence causing the spring to close the valve.
Capillary Tube is a tube with small internal diameter and could be coiled for part of its length. It is installed to the suction line. A filter-drier is sometimes fitted before the tube to remove dirt or moisture from the refrigerant.
This device is simple, does not have any moving part and lasts longer. In order to use this device, the amount of refrigerant in the system must be properly calibrated at factory level.

Due to its lower cost compared to TXV, this metering device is used in units that are produced in large quantity such as room or window air conditioners.
Depending on the capacity design of the system, the capillary tube internal diameter that is commonly used range from 0.031" to 0.065" and the outer diameter from 0.083" to 0.130".

Float Valve is actuated by a float that is immersed in the liquid refrigerant. Both low-side float and high side-float are used to control the flow of liquid refrigerant.
The low-side float helps to maintain a constant level of liquid refrigerant in the evaporator. It opens when there is no liquid in the evap. and closes when there is liquid in the evap.

The high-side float is located at the high pressure side of the system and maintain a constant level of refrigerant in the condenser. When the compressor operates, the condensed refrigerant flows to the float chamber and opens the valve.
This causes the refrigerant to flow into the evaporator where it is stored. As the liquid level falls in the float chamber, the valve opening will close hence preventing the liquid from flowing to the evap.

www.bilkargroup.com
www.bilkarsogutma.com.tr
info@bilkargroup.com
+90 212 343 50 40
+90 553 343 50 40